Settings DebuggerSettings/en - Versionsgeschichte

Alkurz: /* Debug Pin and Field Value Types */

2025-11-04T14:10:41Z

Debug Pin and Field Value Types

← Nächstältere Version		Version vom 4. November 2025, 14:10 Uhr
Zeile 40:		Zeile 40:
	Similar to the above "Allow Invalid Pin and Field Value Types" (which will lead to an Error exception),		Similar to the above "Allow Invalid Pin and Field Value Types" (which will lead to an Error exception),
	enable this to have a debugger opened when the situation arises.		enable this to have a debugger opened when the situation arises.

			=== Treat test result "Pass (Warning)" as "Pass" ===

			(New in 25.2) Since version 25.1, test cases that contain a warning are marked with the status “Pass (Warning)” and displayed with a yellow check mark.

			This behavior can be disabled using this flag. The test result will then be “Pass” again.

	=== Freeze Values are Immutable ===		=== Freeze Values are Immutable ===

2020-06-19T14:00:07Z

Debugger Settings

← Nächstältere Version		Version vom 19. Juni 2020, 14:00 Uhr
Zeile 1:		Zeile 1:
	== Debugger Settings ==		== Debugger Settings ==
			These are found in "''Settings''" - "''Execution''" - "''Debugging''".

	=== Overview ===		=== Overview ===

2018-05-28T15:04:39Z

Debug Expecco

← Nächstältere Version		Version vom 28. Mai 2018, 15:04 Uhr
Zeile 78:		Zeile 78:
	This only applies to user-coded actions (i.e. those with Smalltalk or JavaScript code).		This only applies to user-coded actions (i.e. those with Smalltalk or JavaScript code).
	No debugger is opened for errors in remote procedure calls.		No debugger is opened for errors in remote procedure calls.

			=== Debug Pin and Field Value Types ===
			Controls if a debugger is opened for invalid typed values of pins and field values. If off, an error is reported and the action is finished (unless the exception is handled).

	=== Debug Expecco ===		=== Debug Expecco ===

2018-05-28T15:02:57Z

Enable Halt Messages

← Nächstältere Version		Version vom 28. Mai 2018, 15:02 Uhr
Zeile 57:		Zeile 57:
	halts should be disabled.		halts should be disabled.
	The default is to ignore halts.		The default is to ignore halts.
			<p>

	=== Debug all Exceptions ===		=== Debug all Exceptions ===

2018-05-28T15:02:22Z

Suspend new Actions while a Debugger is Open

← Nächstältere Version		Version vom 28. Mai 2018, 15:02 Uhr
Zeile 83:		Zeile 83:
	In the best of all worlds, there are no such events, but well...		In the best of all worlds, there are no such events, but well...
	This should normally only be turned on by the expecco development team.		This should normally only be turned on by the expecco development team.

			=== Suppress DialogBoxes for Warnings from alert() and warn: ===
			If checked, no such dialog boxes are opened
			Such code is often left in elementary code, during debugging
			of the test suite or while debveloping.
			For a test run you may temporarily disable them,
			in case your boss wants to see a quick demo run.

	=== Suspend new Actions while a Debugger is Open ===		=== Suspend new Actions while a Debugger is Open ===

2018-05-28T14:59:47Z

MessageTally on Execution

← Nächstältere Version		Version vom 28. Mai 2018, 14:59 Uhr
Zeile 94:		Zeile 94:
	in which you want to single step through multiple activities in parallel.		in which you want to single step through multiple activities in parallel.

	=== MessageTally on Execution ===
	If checked, execution times of elementary activities are measured and
	an execution profile is generated after the execution (on the Transcript window).
	This is useful to find out where time is spent for performance optimizations.

2018-05-23T12:31:17Z

Freeze Values are Immutable

← Nächstältere Version		Version vom 23. Mai 2018, 12:31 Uhr
Zeile 43:		Zeile 43:
	(New in 18.1) Enable this (now the default) to make freeze value collections (especially strings and arrays)		(New in 18.1) Enable this (now the default) to make freeze value collections (especially strings and arrays)
	immutable. If passed to tother steps, which try to modify the contents, an error will be reported.		immutable. If passed to tother steps, which try to modify the contents, an error will be reported.
	~~(typically~~ this happens, when a frozen String or Array is passed to an "ElementAt:Put" block,		Typically this happens, when a frozen String or Array is passed to an "ElementAt:Put" block,
	or the string is modified inside a user written elementary block.		or the string is modified inside a user written elementary block.
	If your old test suite does actually depend on a mutable freeze value (which is unlikely),		If your old test suite does actually depend on a mutable freeze value (which is unlikely, bad style and should be punished),
	disable this feature in the settings.		disable this feature in the settings.

2018-03-30T10:40:30Z

Suspend new Actions while a Debugger is Open

← Nächstältere Version		Version vom 30. März 2018, 10:40 Uhr
Zeile 93:		Zeile 93:
	You should only uncheck this, if you are about to debug producer/consumer scenarios,		You should only uncheck this, if you are about to debug producer/consumer scenarios,
	in which you want to single step through multiple activities in parallel.		in which you want to single step through multiple activities in parallel.


	=== MessageTally on Execution ===		=== MessageTally on Execution ===

2018-03-30T10:40:22Z

Debug Expecco

← Nächstältere Version		Version vom 30. März 2018, 10:40 Uhr
Zeile 83:		Zeile 83:
	In the best of all worlds, there are no such events, but well...		In the best of all worlds, there are no such events, but well...
	This should normally only be turned on by the expecco development team.		This should normally only be turned on by the expecco development team.


	=== Suspend new Actions while a Debugger is Open ===		=== Suspend new Actions while a Debugger is Open ===

2018-03-30T10:40:14Z

Debug Handled Exceptions in Activity Code

← Nächstältere Version		Version vom 30. März 2018, 10:40 Uhr
Zeile 77:		Zeile 77:
	This only applies to user-coded actions (i.e. those with Smalltalk or JavaScript code).		This only applies to user-coded actions (i.e. those with Smalltalk or JavaScript code).
	No debugger is opened for errors in remote procedure calls.		No debugger is opened for errors in remote procedure calls.


	=== Debug Expecco ===		=== Debug Expecco ===